Eibach sportline springs seat leon 2.0 tfsi & cupra r 2006- 1130/930 kg. This product page has been automatically translated. If you have any questions, do not hesitate to contact us.Eibach sportline performance suspension springs sport for. Eibach sportline performance springs sport for. For manufacturer and model: for manufacturer and model: Seat type 1p (1p1) hatchback from year of manufacture 11.2006. Axle load in kg front / rear: max. Axle load in kg front / rear: 1130/930. Lowering in mm front / rear approx. Lowering in mm front / rear approximately: 20 / 30. Engine types: engine types: 2.0 tfsi / 2.0 cupra r. Expert report / abe: certificate / abe: with general operating license (abe).
Carton in mm: cardboard packaging in mm: 636x377x170. Notes: Please read the yellow chart below!
Tips: Please read the yellow chart below! Eibach sportline performance springs sport the first choice of motorsport fans around the world.
Sports suspension and pure optics lower the vehicle up to 50 mm optimal attraction by lowering handling type motor sports progressive spring design component certification tip: in order to ensure adequate preload of sportline springs, we, as well as the manufacturer, recommend the installation of shortened sport dampers such as bilstein b8 shock absorbers. If you need advice in this regard, please contact us with a message indicating your contact information. Eibach sportline performance springs sport # 1 choice of automotive enthusiasts in the world!
Springs and appearance of pure sport suspension lower ride height - up to 50 mm optimal attraction by lowering sport-type handling automotive progressive suspension features designed and tested to work perfectly with the original shock absorbers tip: eibach recommends to install shorter \If you need help, contact us. How do I check if this item fits my vehicle? Three simple steps that you can check yourself using your registration certificate and vehicle registration document. You will find an example of a new registration certificate as an example image from the description of the article added above. At four digit hsn (mpn) and the 3 digits tsn (type the key number, the first 3 characters) you can check which items of our shop are compatible with your vehicle.See entry of the list of vehicles above! These numbers are found under 2.1 and 2.2 in your registration certificate part i (vehicle registration), in our photo above with red highlighting.
Please check the following items front and rear axle loads and compare them with our description. In your registration certificate (vehicle registration), this information is under 7.1 and 7.2 listed.(In the image example \In the end, this is still year and the remarks to check the build year must be in the time window specified by us build this information is in our data table at the top of the line \and the associated references in the important yellow reference table below. If different or if you have any doubt, contact our qualified service team!
Scoreboard: Please refer to the product description above for any relevant information. A l l e m e n e to me e e e s e.
German: Unless otherwise specified, the suspension specified in the catalog will be reduced by the amount of the factory lowering for vehicles equipped with an ex-works sports suspension. Unless otherwise specified, factory-fitted vehicles with higher chassis p. Off-road character, cross-over or pacts for bad roads are excluded from the use of our products.For article / vehicle classification, the details in the parts report or in the abe are decisive. For this, among other things, the receipt number this type of vehicle registration point or on the vehicle identification plate to search! To compare with the information in the report. Before assembly, please check with the parts certificate / abe if the delivered items (see marking of parts) are approved for your vehicle (see application area). In case of discrepancy, the parts can not be installed - in this case, please contact the seller.
You can \The number must not be upside down. After mounting the spring / suspension components, it is imperative to check the wheel settings. If the shock absorbers of the series are no longer fully functional and significantly less effective, we strongly recommend that you replace them with new shock absorbers of the series or sport dampers. The lowering performance is negatively affected by worn or defective dampers. Of course, if you need new shock absorbers, we will be happy to advise you.
At sportline springs we recommend the installation of sport dampers such as bilstein b8. All wheel / tire combinations approved by the wheel type controllers may be used. Wheel or wheel wheel ratio requirements must be met, except for the standard suspension requirement.
Depending on the engine, gear, equipment and vehicle tolerances, lowering of a few mm may vary the specified values. The degree of lowering is always reduced by the amount of the lowering at the factory.
The user-friendliness of our products concerns standard format vehicles. For conversions and special accessories also applies to standard accessories! Such as the installation of a special braking system (for example a ceramic braking system), zenralverschluss wheels, sports suspensions, lpg system, etc.
Our products can not be used. Dimensions shown are for standard new vehicles. Measuring points: vertical distance from the center of the wheel hub to the lower edge of the wing. Basically, the dimensions specified are nominal values, which may vary depending on the vehicle.
If the standard suspension has the electronic register control, its functionality is removed when using b12 chassis or pro street s. The error message displayed on the on-board computer may be disabled by an authorized workshop. If available for your vehicle, we recommend that you use pro-tronic to remove the error message.
Except vehicles with level control. Except for vehicles with electronic suspension adjustment. For a lowering of more than 40 mm and a diameter of the right drive shaft greater than 42 mm, possibly.
The series stabilizer to replace. The set of stabilizers required here is available from eibach part number: e40-85-005-01-10 in well-stocked specialty stores.
Not suitable for the variant \Increase the axle trailer in operation (see parts of opinions). For vehicles with multi-link rear suspension (independent suspension). For vehicles with torsion beam rear axle (rigid axle).
For vehicles without chassis amg. Only for export, not available in Germany. Not for \Only for vehicles with standard s-line suspension.
Only for vehicles without standard s-line suspension. Service Information: Please refer to the product description above for applicable instructions. C the m on n e s. English: if not designated separately, for vehicles with suspension lowered by the original manufacturer.
If not named separately, original suspension vehicles p. Offroad group, crossover are excluded from the use of our products. The specifications indicated in the approval are for the classification of the object / vehicle. Please check the homologation number of your car and compare with the homologation. Letter k in your registration certificate or find on the nameplate of your car!
(see marking) are approved for your vehicle (see field of use). Mounting - we recommend having our system installed by a qualified workshop only. Mounting position - you can read the fingerprint. Wheel adjustment - it is necessary to adjust the wheel. Shock absorbers - if the standard shocks are not fully operational and their efficiency is exhausted, we strongly recommend replacing them with new shock absorbers.
The performance of the new suspension should not be improved by the use of old dampers. If you need new shock absorbers, we can help you if necessary. The installation of sport-shock absobers is recommended. By way of example, bilstein b8 all wheel / tire combinations are possible and are published by the wheel type test institution. Depending on the engine, the gearbox / transmission, the equipment and the tolerances of the vehicle.
The lowering dimension is achieved by the manufacturer. The applicability of our standard car offers. In all cases of reconstruction (even with original accessories), such as the installation of a brake accessory system (ceramic brakes, for example), a sports suspension, a system of lpg (liquefied petroleum gas), for example, the use of our products may be excluded. The measurements given refer to the new standard cars.Measuring points: vertical distance between the middle of the wheel and the lower edge of the mud wing. Generally, the measurements shown are nominal values, which may vary depending on each car. If your vehicle has a damper control in series, this will no longer be the case with the b12 suspension kit or pro street s. You want to see a problem code. This can be reprogrammed by an official dealer / dealer.
If available for your vehicle, we recommend using pro-tronic to avoid the trouble code. When the car is lowered to 40 mm in combination with a shaft larger than 42 mm in diameter, the original stabilizer bar has been replaced by the eibach anti-roll kit, part no. Not suitable for the \Increased load on the axle when using the trailer (see approval). For cars with independent suspension at the rear axle. For cars with rear axle rear.
For vehicles without suspension amg. Only export - neither available in germany - only without component certificate! Not for \Only for vehicles with s line suspension.Only for vehicles without s line suspension. Products that may be of interest to you. Eibach pro-kit springs for bmw series 3 e46 limo 0 2.1 998 <\/ span> -04.2005 970/1100 kg. Rgm bumper protection of origin black abs dacia sandero ii black also stepway from 2012. Protection bumper rgm of origin abs black ford kuga i suv 03.2008 -0 2.2 013. Protection bumper rgm of origin abs black vw golf vi cabriolet bauj. Original rgm smooth load abs protection black abs vw t5 m. Bumper protection rgm of origin abs black vw iv caddy also maxi of the year 05.2015. Bumper protector rgm original abs black bumper painted vw caddy 2004-15. Bumper protection rgm of origin abs black opel mokka x suv of facelift 0 7.2 016. 2.0 tfsi / 2.0 cupra r. Maximum achslast vorne / hinten 1130/930 kg. The item \suspension, direction \ springs \The seller is \This item can be shipped to the following country: